.svg&w=240){kind=small}
B&R 8EI034HCSS0.XXXX-1
ACOPOS P3 servo drive, 3x 200-480 VAC, 34 A, SafeMOTION
- MPN
- 8EI034HCSS0.XXXX-1
Price and lead time confirmed within 1 business day
Request a Quote
- 12-month warranty (new) · 3-month (used/refurbished)
- 30-day returns, no restocking fee on unused parts
- Ships via
What is the B&R 8EI034HCSS0.XXXX-1?
ACOPOS P3 servo drive, 3x 200-480 VAC, 34 A, SafeMOTION, 1 axis, AS, cold plate or pass-through mounting
Specifications
General information
| Support – Dynamic node allocation (DNA) | Yes |
| Certifications – CE | Yes |
| Certifications – UKCA | Yes |
| Certifications – CRA (Cyber Resilience Act) | In preparation |
| Certifications – UL | cULus E225616; Power conversion equipment |
| Slots for plug-in modules | 1 |
Mains connection
| Terminal connection cross section – With wire end sleeve | 0.75 to 16 mm² |
| Terminal connection cross section – UL/C-UL-US | 20 to 4 AWG |
| Terminal connection cross section – CSA | 20 to 4 AWG |
| Network configurations | TT, TN, TN-S, TN-C-S, IT (note: Operation on TT and IT power systems and on TN power systems that are not grounded to a star point is only permitted for 8EI servo drives with 8ZELxxxx Rev. D0 and higher. See the device information on the left side cover of the 8EI servo drive. Remove IT jumper X10 before operating in IT networks!) |
| Mains input voltage | 3x 200 VAC to 480 VAC ±10% |
| Frequency | 50 / 60 Hz ±4% |
| Installed load | Max. 26.4 kVA |
| Inrush current | Max. 100 A |
| Switch-on interval | 120 s |
| Integrated line filter per EN 61800-3, category C3 | No (note: A line filter must be connected. CE compliance can only be ensured by connecting an upstream B&R line filter (8B0F...). In extreme cases, using line filters from 3rd-party manufacturers can result in irreparable damage to the ACOPOS P3 8EI servo drive.) |
| Power dissipation at device nominal power without braking resistor | [81 W + 9.7 V * I + 8.4 W/kW * P out + 0.25 Ω * I 2 BR + P VSLOT ] * 1.1 |
| Power dissipation remaining in the control cabinet | Pv_inside = 0.510 * Pv + 1.624 * (T_amb – T_inside) |
| Max. line length | 3 m (note: Maximum line length between line filter and mains connection on the module.) |
DC bus connection
| Reduction of continuous power depending on mains input voltage – Mains input voltage <3x 400 VAC | 14 kW * (Mains input voltage [V] / 400 V) |
| Terminal connection cross sections – With wire end sleeves | 0.75 to 16 mm² |
| Terminal connection cross sections – UL/C-UL-US | 20 to 4 AWG |
| Terminal connection cross sections – CSA | 20 to 4 AWG |
| Continuous power | 14 kW (note: Valid for mains input voltage ≥3x 400 VAC. The sum of the continuous power values on all motor connections and the power of the DC bus connector is not permitted to exceed this value.) |
| DC bus capacitance | 1680 µF |
| Max. line length | 3 m (note: This value applies to unshielded wiring inside a control cabinet. Maximum length of the DC bus wiring inside a control cabinet.) |
24 VDC power supply
| Terminal connection cross sections – With wire end sleeves | 0.25 to 4 mm² |
| Terminal connection cross sections – UL/C-UL-US | 24 to 8 AWG |
| Terminal connection cross sections – CSA | 24 to 8 AWG |
| Input voltage | 24 VDC ±25% |
| Input capacitance | 5500 μF |
| Current consumption | 2 A + Current for motor holding brake (note: Current consumption depends on the respective configuration of the ACOPOS P3 8EI servo drive. The inrush current of the 24 VDC power supply is not limited by the module.) |
| Max. line length | 30 m |
Motor connection
| Accuracy of the safe current – SIL 2 / PL d / Cat. 3 | Hardware upgrade 1.10.2.x: 9.098 A; Hardware upgrade 1.10.3.0 or later: 7.614 A |
| Accuracy of the safe current – SIL 2 / PL d / Cat. 2 | 3.804 A |
| Accuracy of the safe current – SIL 2 / PL d / Cat. 3 | Hardware upgrade 1.10.2.x: 7.732 A; Hardware upgrade 1.10.3.0 or later: 6.196 A |
| Accuracy of the safe current – SIL 2 / PL d / Cat. 2 | 2.666 A |
| Reduction of continuous current depending on ambient temperature – Switching frequency 5 kHz | In preparation |
| Reduction of continuous current depending on ambient temperature – Switching frequency 10 kHz | In preparation |
| Reduction of continuous current depending on ambient temperature – Switching frequency 20 kHz | In preparation |
| Reduction of continuous current depending on ambient temperature – Switching frequency 5 kHz | In preparation |
| Reduction of continuous current depending on ambient temperature – Switching frequency 10 kHz | In preparation |
| Reduction of continuous current depending on ambient temperature – Switching frequency 20 kHz | In preparation |
| Reduction of continuous current depending on installation elevation – Starting at 500 m above sea level | 3.4 A eff per 1000 m |
| Protective measures – Overload protection | Yes |
| Protective measures – Short-circuit and ground fault protection | Yes |
| Variant – U, V, W, PE | Connector |
| Variant – Shield connection | Yes; Clamping range of the grounding clamp: 17 to 30 mm |
| Terminal connection cross section – With wire end sleeve | 0.75 to 16 mm² |
| Terminal connection cross section – UL/C-UL-US | 20 to 4 AWG |
| Terminal connection cross section – CSA | 20 to 4 AWG |
| Max. motor line length depending on switching frequency – Switching frequency 5 kHz | 75 m |
| Max. motor line length depending on switching frequency – Switching frequency 10 kHz | 35 m |
| Max. motor line length depending on switching frequency – Switching frequency 20 kHz | 20 m |
| Quantity | 1 |
| Continuous power per motor connection | 14 kW (note: Valid under the following conditions: 560 VDC DC bus voltage, 5 kHz switching frequency, 40°C ambient temperature, installation elevation <500 m above sea level, no derating due to cooling type.) |
| Continuous current per motor connection | 34 A eff (note: Valid under the following conditions: 560 VDC DC bus voltage, 5 kHz switching frequency, 40°C ambient temperature, installation elevation <500 m above sea level, no derating due to cooling type.) |
| Peak current per motor connection | 85 A eff |
| Peak power output | 35 kW |
| Nominal switching frequency | 5 kHz |
| Possible switching frequencies | 2.5 / 5 / 10 / 20 kHz (note: B&R recommends operating the module at its nominal switching frequency. Operating the module at a higher switching frequency for application-specific reasons reduces the continuous current and increases CPU utilization.) |
| Insulation stress of the connected motor per IEC TS 60034-25:2004 | Limit value curve A (note: Only applies when using B&R motor cables and B&R motors.) |
| Max. output frequency | 598 HzPower unit: Limit speed exceeded")."> |
Motor holding brake connection
| Terminal connection cross section – With wire end sleeve | 0.75 to 16 mm² |
| Terminal connection cross section – UL/C-UL-US | 20 to 4 AWG |
| Terminal connection cross section – CSA | 20 to 4 AWG |
| Protective measures – Overload and short-circuit protection | Yes |
| Protective measures – Open-circuit monitoring | Yes |
| Protective measures – Undervoltage monitoring | Yes |
| Quantity | 1 |
| Output voltage | Depends on the input voltage on connector X2 (note: At values <22.9 V, under voltage monitoring is triggered and the servo drive signals error 6029 or 6055. In this case, the input voltage at connection X2 (24 VDC power supply) is too low and must be increased.) |
| Continuous current per connection | 6.5 A |
| Max. internal resistance | 0.25 Ω |
| Extinction potential | Approx. 30 V |
| Max. extinction energy per switching operation | 15 Ws |
| Max. switching frequency | 0.5 Hz |
| Response threshold for open-circuit monitoring | Approx. 120 mA |
| Response threshold for undervoltage monitoring | Approx. 23 V |
| Max. breaking current SBC | 200 mA |
| Max. line length | 75 m (note: During configuration, it is necessary to check if the minimum voltage can be maintained on the holding brake with the intended line length. For the permissible operating voltage range of the holding brake, see the user documentation for the motor being used.) |
Braking resistor
| Protective measures – Overload protection | No |
| Protective measures – Short-circuit and ground fault protection | Short-circuit protection: Yes; Ground fault protection: No |
| Peak power output | 45 kW |
| Continuous power | 4 kW |
| Minimum braking resistance (ext.) | 13 Ω |
| Max. line length | 3 m |
Fieldbus
| Type | POWERLINK V2 controlled node (CN) |
| Variant | 2x RJ45, shielded, 2-port hub |
| Line length | Max. 100 m between 2 stations (segment length) |
| Transfer rate | 100 Mbit/s |
Encoder interfaces
| Electrical isolation – Encoder - ACOPOS P3 | No |
| Encoder power supply – Short-circuit proof | Yes |
| Encoder power supply – Overload-proof | Yes |
| Encoder power supply – Output voltage | Configurable; Typ. 11.45 V ±0.1 V / 5.2 V ±0.1 V |
| Encoder power supply – Load capacity | Max. 300 mA |
| Encoder power supply – Sense lines | 2, compensation of max. 2x 0.7 V |
| Synchronous serial interface – Minimum | 2.0 V |
| Synchronous serial interface – Maximum | 6.0 V |
| Synchronous serial interface – Signal transmission | RS485 (note: Except encoder type HIPERFACE DSL.) |
| Synchronous serial interface – Data transfer rate | Depends on the configured encoder type |
| Quantity | 1 |
| Type | Digital multi-encoder interface, configurable (note: The encoder type is not predefined from the factory. The encoder type necessary in each case must be configured in Automation Studio.) |
| Connections | 8-pin female Mini I/O connector |
| Status indicators | None (note: The direction of rotation of the encoder can be displayed on the 8EAD0000.000-1 display module.) |
| Max. encoder cable length | 75 m ; Depends on the cross section of the power supply wires in the encoder cable |
| Max. power consumption per encoder interface | P ENCODER [W] = U 24V [V] * (I ENCODER [A] * 0.7) + 0.5 W (note: I ENCODER ... Current consumption of the encoder U 24V ... Input voltage on the +24 VDC input of the module) |
Trigger inputs
| Electrical isolation – Input - ACOPOS P3 | Yes |
| Electrical isolation – Input - Input | Yes |
| Input voltage – Nominal | 24 VDC |
| Input voltage – Maximum | 30 VDC |
| Switching threshold – Low | <5 V |
| Switching threshold – High | >15 V |
| Switching delay – Rising edge | <51 µs |
| Switching delay – Falling edge | <52 µs |
| Terminal connection cross section – With wire end sleeve | 0.25 to 2.5 mm² |
| Terminal connection cross section – UL/C-UL-US | 26 to 12 AWG |
| Terminal connection cross section – CSA | 26 to 12 AWG |
| Quantity | 2 |
| Circuit | Sink |
| Input current at nominal voltage | 7 mA |
| Modulation compared to ground potential | Max. ±38 V |
| Max. line length | 100 m |
Temperature sensor connection
| Quantity | 1 |
| Resistance range | 500 Ω to 5 kΩ |
Support
| Motion system – mapp Motion | 5.05.0 and higher |
| Motion system – ACP10/ARNC0 | 5.03.0 and higher |
Electrical properties
| Energy efficiency (IE classification) – Power dissipation relative to continuous apparent power | IE2 (10,25) 1% ; IE2 (50,25) 1% ; IE2 (10,50) 1.2% ; IE2 (50,50) 1.3% ; IE2 (90,50) 1.4% ; IE2 (10,100) 1.9% ; IE2 (50,100) 2.1% ; IE2 (90,100) 2.4% |
| Energy efficiency (IE classification) – Nominal losses in standby mode | 15.8 W |
Operating conditions
| Permissible mounting orientations – Hanging vertically | Yes |
| Permissible mounting orientations – Horizontal, face up | No |
| Permissible mounting orientations – Standing horizontally | No |
| Installation elevation above sea level – Nominal | 0 to 500 m |
| Installation elevation above sea level – Maximum | 4000 m (note: For operation on phase-grounded/center-grounded delta networks (TT and TN) and IT networks, the value is reduced to 2000 m.) |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Overvoltage category per EN 61800-5-1 | III |
| Degree of protection per EN 60529 | IP20 (note: The specified degree of protection is only met if either the slot cover is installed on the module or an 8EAC plug-in module is installed and suitable terminals are connected to all connectors and all fans are installed.) |
Ambient conditions
| Temperature – Minimum | -25°C |
| Temperature – Nominal | 5 to 40°C |
| Temperature – Maximum | 55°C |
| Temperature – Storage | -25 to 55°C |
| Temperature – Transport | -25 to 70°C |
| Relative humidity – Operation | 5 to 85 %, non-condensing |
| Relative humidity – Storage | 5 to 95% |
| Relative humidity – Transport | 95% at 40°C |
Mechanical properties
| Dimensions – Cold plate | 281.5 mm (with 8EXA front cover: 284 mm) (note: These dimensions refer to the actual device dimensions including the respective mounting plate. Additional spacing above and below the devices must be taken into account for mounting, connections and air circulation.) |
| Dimensions – Pass-through mounting | 277.5 mm (with 8EXA front cover: 280 mm) (note: These dimensions refer to the actual device dimensions including the respective mounting plate. Additional spacing above and below the devices must be taken into account for mounting, connections and air circulation.) |
| Dimensions – Width | 133 mm (note: These dimensions refer to the actual device dimensions including the respective mounting plate. Additional spacing above and below the devices must be taken into account for mounting, connections and air circulation.) |
| Dimensions – Height | 374 mm (note: These dimensions refer to the actual device dimensions including the respective mounting plate. Additional spacing above and below the devices must be taken into account for mounting, connections and air circulation.) |
| Dimensions – Depth | 264.50 mm (with 8EXA front cover: 267 mm) (note: These dimensions refer to the actual device dimensions including the respective mounting plate. Additional spacing above and below the devices must be taken into account for mounting, connections and air circulation.) |
| Weight | 9.4 kg |
Accessories
Required accessories (order separately)
| 8EMC0060000.0000-2 | Cold-plate mounting — ACOPOS P3 mounting plate, 6 slots, cold plate mounting |
| 8EMC0040000.0000-2 | Cold-plate mounting — ACOPOS P3 mounting plate, 4 slots, cold plate mounting |
| 8EMC0020000.0000-2 | Cold-plate mounting — ACOPOS P3 mounting plate, 2 slots, cold plate mounting |
| 8EXF500.0000-00 | Fan modules — ACOPOS P3 fan module for mounting plate 8EMFxxx0000.0000-1 single-width |
| 8EXF400.0000-00 | Fan modules — ACOPOS P3 fan module for mounting plate 8EMFxxx0000.0000-1 double-width |
Optional accessories (26)
| 8EAD0000.000-1 | Display modules — An 8EAD display module can be plugged into the X9 interface of an 8EI servo drive to display information about the drive and set its parame… |
| 8EXF300.0000-00 | Fan modules — ACOPOS P3 ELKO fan module, replacement fan for ACOPOS P3 servo drive double-width (8EI017xxD/8EI022xxD/ 8EI024/8EI034/8EI044) |
| 8EXF200.0000-00 | Fan modules — ACOPOS P3 fan module, replacement fan for ACOPOS P3 servo drive double-width (8EI017xxD/8EI022xxD/ 8EI024/8EI034/8EI044) |
| 8EXA300.0020-00 | Front covers — 8EXA covers protect the interfaces on the front of ACOPOS P3 8EI servo drives and contribute to a uniform appearance inside the control cab… |
| 8EXA300.0010-00 | Front covers — 8EXA covers protect the interfaces on the front of ACOPOS P3 8EI servo drives and contribute to a uniform appearance inside the control cab… |
| 8B0F0550H000.000-1 | Line filters passive — Wide mains input voltage range; Optimally suited for ACOPOSmulti 8B0P power supply modules; Compliance with limit values per CISPR11, group… |
| 8B0F0300H000.000-1 | Line filters passive — Wide mains input voltage range; Optimally suited for ACOPOSmulti 8B0P power supply modules; Compliance with limit values per CISPR11, group… |
| 8B0F0160H000.000-1 | Line filters passive — Wide mains input voltage range; Optimized for ACOPOSmulti 8B0P power supply modules and ACOPOS P3; Compliance with limit values per CISPR11… |
| 8EAC0152.001-1 | Plug-in modules — ACOPOS P3 plug-in module, analog multi-encoder interface |
| 8EAC0151.001-1 | Plug-in modules — ACOPOS P3 plug-in module, incremental encoder interface |
| 8EAC0150.001-1 | Plug-in modules — ACOPOS P3 plug-in module, digital multi-encoder interface |
| 8EAC0130.000-1 | Plug-in modules — ACOPOS P3 plug-in module, 8 digital I/O 24 V (4x 400 mA, 4x 100 mA) individually configurable as inputs or outputs, 2 digital I/O 24 V 2 A… |
| 8EAC0122.001-1 | Plug-in modules — Resolver interface for installation in ACOPOS P3 servo drives; Encoder monitoring; High resolution ACOPOS P3 plug-in module, resolver inter… |
| 8SCSE02.0200-00 | Shield component sets — ACOPOS P3 shield component set: 1x shield connection clamp type SK20 |
| 8SCSE02.0100-00 | Shield component sets — ACOPOS P3 shield component set: 1x shield connection clamp type SK14 |
| 8SCSE01.0200-00 | Shield component sets — Shield component set 8SCSE01.0200-00 is installed on the underside of ACOPOS P3 8EI servo drives with a width of 133 mm and consists of a s… |
| 8TB4104.227F-10 | Terminal blocks — 4-pin push-in terminal block, 1-row, pitch: 10.16 mm, label 4: DC-, DC-, DC+, DC+ coding F: 0101 |
| 8TB4104.224G-10 | Terminal blocks — 4-pin push-in terminal block, 1-row, pitch: 10.16 mm, label 4: PE W V U, coding G: 0110 |
| 8TB4104.222L-10 | Terminal blocks — 4-pin push-in terminal block, 1-row, pitch: 10.16 mm, label 2: PE L3 L2 L1, coding L: 1010 |
| 8TB4103.222A-10 | Terminal blocks — 3-pin push-in terminal block, one-row, pitch: 10.16 mm, label 2: PE RB- RB+, coding A: 000 |
| 8TB3202.222C-40 | Terminal blocks — 2-pin push-in terminal block, 2-row, with locking mechanism, pitch: 7.62 mm, label 2: COM 24 V, coding C: 10 |
| 8TB3102.222C-20 | Terminal blocks — 2-pin push-in terminal block, 1-row, with locking mechanism, pitch: 7.62 mm, label 2: COM 24 V, coding C: 10 |
| 8TB2104.223L-00 | Terminal blocks — 4-pin push-in terminal block, 1-row, pitch: 5.08 mm, label 3: T- T+ B- B+, coding L: 1010 |
| 8TB2104.2210-00 | Terminal blocks — 4-pin push-in terminal block, 1-row, pitch: 5.08 mm, label 1: Numbered consecutively |
| 8EZI044HSS.2302-0 | Terminal set — Terminal block set for ACOPOS P3 modules 8EI0*4**SS0.****-1: 1x 8TB2104.2210-00, 1x 8TB3202.222C-40, 1x 8TB4104.224G-10, 1x 8TB2104.223L-00… |
| 8EZI044HSS.2201-0 | Terminal set — Terminal block set for ACOPOS P3 modules 8EI024H*SS, 8EI034H*SS, 8EI044H*SS: 1x 8TB2104.2210-00, 1x 8TB3102.222C-20, 1x 8TB4104.224G-10, 1x… |
Downloads & documentation
Official documents from B&R, downloaded directly from the manufacturer.
Data sheets & manuals
CAD & dimension drawings
8EI034HCSS0.XXXX-1: frequently asked questions
When can 8EI034HCSS0.XXXX-1 be shipped?
8EI034HCSS0.XXXX-1 is sourced on request — request a quote and we'll confirm the exact availability and shipping timeline for this specific unit.
Can I pick up 8EI034HCSS0.XXXX-1 in person?
Local pickup from our Groningen, Netherlands warehouse may be possible — contact us before ordering to check availability and arrange a collection time.
Is express delivery available?
Yes — mention it when you request a quote for 8EI034HCSS0.XXXX-1 and we'll include express shipping options in our reply.
My factory is down and I need this urgently — can you help?
For a critical breakdown, contact us directly at +31 (0)50-7110348 or sales@partnerplc.com — we can look into same-day courier or dedicated taxi/hotshot delivery for 8EI034HCSS0.XXXX-1, subject to availability and destination.
More B&R parts
B&R 8EI034HCSS0.XXXX-1Price and lead time confirmed within 1 business day
Request a Quote