Honeywell HPF-PS6

PS Series Remote Power Supply 6A

MPN
HPF-PS6
Price and lead time confirmed within 1 business day
Request a Quote
  1. 1We check stock, condition and lead time
  2. 2You get a written quote by email
  3. 3Approve it and we ship — in-stock parts within 1 business day

A real person replies, typically within 1 business day — see our privacy policy.

  • 12-month warranty (new) · 3-month (used/refurbished)
  • 30-day returns, no restocking fee on unused parts
  • 100% positive eBay feedback
  • Ships via

Have spare Honeywell parts? We buy surplus →

What is the Honeywell HPF-PS6?

The PS Series Power Supplies provide more power and higher number of inputs and output circuits with the flexibility to pair any input with any output. The PS Series also enables the ability to convert from Class B to Class A circuits by adding a ZNAC card without losing any circuits (unlike competition where class B to A conversion reduces your circuits by half). Each circuit can be individually programmed (using DIP switches) to be a NAC output, used for resettable AUX power, non-resettable AUX power or door holder power. This provides unprecedented flexibility in system design.

PS series supports SSD, Wheelock, Gentec and Amseco sync protocol and it is UL listed to provide synchronized cascade up to 4 levels deep (unlike competition who provides up to 3) and through different configurations you may have up to 40 power supplies in sync or up to 400A power. This helps to provide synchronized power expansion for larger applications.

The PS Series is equipped with 3 system health LED indicators (Power, Battery/Charger Fault, and Ground Fault). In addition each available output circuit also has 2 status LEDs - output status and trouble. The trouble LEDs flash in different blink patterns to indicate type of trouble such as open or short circuit. This allows faster diagnostics by pinpointing problematic areas and reason quickly. It also has “Display trouble history mode” which shows past history of troubles on the system

A removable door in PS Series gives better access to wire up the unit, especially in tight spaces allowing reduced installation time and more knockouts provides more flexibility in cabling.

PS series accepts a wide range for EOL resistor values (2kohms to 27kohms) which means installers no longer have to go look for or change EOL resistors in a retrofit application which saves time and money

Larger cabinet space to house bigger batteries (7/18AH) and ability to mount SLC modules within the cabinet. It saves cost of additional mounting cabinets for batteries/ modules unlike competition where you have to mount and wire up modules external to the power supply.

Features & Benefits:

Up to five independently- configurable, power-limited output circuits for:

Class B and/or Class A NACs

Class B and/or Class A resettable or non-resettable 24V auxiliary power

door holder power

Converts from Class B to Class A wiring without losing any outputs

Using the ZNAC-PS converter card (sold separately)

Optimal for powering four-wire smoke detectors, annunciators, and other system peripherals requiring regulated power

Configurable for ANSI® Temporal 3 or Temporal 4 coded output

UL-Listed NAC synchronization using System Sensor®, Wheelock®, Gentex®, or AMSECO® appliances

Synchronization can be triggered from FACP NAC/remote sync outputs, cascaded power supply, or a control module, single or multi, which may be housed within the power supply cabinet

Ability to cascade up to four levels

Two fully-isolated input/control circuits which can be programmed to any output

Two Form C normally-closed trouble relays for AC Trouble and General Trouble, Ground Fault relay available on Canadian models only

6 amp full load output, respectively, with 3 A maximum/circuit

Individual NAC power and trouble LEDs for diagnostic efficiency

Trouble history modes for diagnostic support

Wide range end-of-line supervision value (normal: 2K-27K ohms)

Selectable earth fault detection (enable or disable)

AC trouble report delay timer

Completely configurable via onboard DIP switches, no extra software required

Self-contained in compact, locking cabinet constructed of heavy gauge steel with a corrosion-resistant powder coat chip and scratch-resistant finish

Cabinet designed with ten double knockouts and a removable door for ease of installation and wiring

Includes integral battery charger capable of charging up to 33 AH batteries

Cabinet can house two 7 AH or 18 AH batteries

Certifications:

UL Listed: HPF-PS6(B)(E): S24562

CSFM Approved: HPF-PS6(B)-7315-1637:0505

FDNY Approved

FM Approved

Honeywell HPF-PS6 — The PS Series 6A remote power supply with battery charger and 5 configurable outputs, gives A&Es, dealers, installers and end users more flexible and efficient options for meeting today’s installation, set-up and servicing needs for power supplies. PartnerPLC sources new, surplus and discontinued Honeywell parts — request a quote for price, condition and lead time.

Specifications

Product

LifecycleActive

Ordering codes

Part numbers on this product pageHPF-PS6, HPF-PS6B, HPF-PS6E

HPF-PS6: frequently asked questions

When can HPF-PS6 be shipped?

HPF-PS6 is sourced on request — request a quote and we'll confirm the exact availability and shipping timeline for this specific unit.

Can I pick up HPF-PS6 in person?

Local pickup from our Groningen, Netherlands warehouse may be possible — contact us before ordering to check availability and arrange a collection time.

Is express delivery available?

Yes — mention it when you request a quote for HPF-PS6 and we'll include express shipping options in our reply.

My factory is down and I need this urgently — can you help?

For a critical breakdown, contact us directly at +31 (0)50-7110348 or sales@partnerplc.com — we can look into same-day courier or dedicated taxi/hotshot delivery for HPF-PS6, subject to availability and destination.

More Honeywell parts

Honeywell HPD4 – Power Distribution Board
Honeywell
HPD4

Power Distribution Board

Honeywell HPD8 – Power Distribution Board - and CB
Honeywell
HPD8

Power Distribution Board - and CB

Honeywell HPDC121A – Power Supply
Honeywell
HPDC121A

Power Supply

Honeywell HPF-PS10 – PS Series Remote Power Supply 10A
Honeywell
HPF-PS10

PS Series Remote Power Supply 10A

Honeywell HPF-PS6Price and lead time confirmed within 1 business day
Request a Quote