B&R X20DC1073
견적 요청
요약 정보
| 재고 상태 | 요청 시 확인 |
| 카테고리 | Counter functions |
| 라이프사이클 | active |
| 보증 | 12개월(신품) · 3개월(중고/재제조) |
배송 & 재고
X20DC1073은(는) 언제 배송될 수 있나요?
X20DC1073은(는) 요청 시 소싱됩니다 — 견적을 요청해 주시면 이 특정 제품의 정확한 재고 및 배송 일정을 확인해 드립니다.
X20DC1073을(를) 직접 픽업할 수 있나요?
네덜란드 흐로닝언 창고에서 직접 픽업이 가능할 수 있습니다 — 주문 전에 연락하셔서 재고와 픽업 시간을 확인해 주세요.
특급 배송이 가능한가요?
네 — X20DC1073에 대한 견적을 요청하실 때 말씀해 주시면 답변에 특급 배송 옵션을 포함해 드립니다.
공장 가동이 중단되어 긴급히 필요합니다 — 도와주실 수 있나요?
긴급 고장 상황이시라면 +31 (0)50-7110348 또는 sales@partnerplc.com으로 직접 연락해 주세요 — 재고 및 배송지에 따라 X20DC1073에 대한 당일 택배 또는 전용 긴급 배송을 검토해 드립니다.
SinCos encoder interfaceEncoder input monitoring5 VDC and GND for encoder supplyNetTime timestamp: Position timeCan be used with a SafeLOGIC controller The module is equipped with a SinCos encoder interface. The input signals are monitored. This makes it possible to detect open or shorted lines as well as encoder supply failures.SinCos encodersSinCos encoders with 1 Vss are mostly used in linear drives and systems with high-resolution optical or magnetic position measurement systems. The module can process input signals with a frequency of up to 400 kHz.NetTime timestamp for the positionIt is not just the position value that is important for highly dynamic positioning tasks, but also the exact time the position is measured. The module is equipped with a NetTime function for this that supplies a timestamp for the recorded position with microsecond accuracy.The timestamp function is based on synchronized timers. If a timestamp event occurs, the module immediately saves the current NetTime. After the respective data is transferred to the CPU, including this precise moment, the CPU can then evaluate the data using its own NetTime (or system time), if necessary.
사양
Specifications
| I/O module | 1x SinCos input |
| B&R ID code | 0xAEC6 |
| Status indicators | Counting direction, operating state, module status |
| Module run/error | Yes, using LED status indicator and software |
| Counting direction | Yes, using LED status indicator |
| Bus | 0.01 W |
| Internal I/O | 1.3 W |
| Additional power dissipation caused by actuators (resistive) [W] | - |
| Type of signal lines | Shielded lines must be used for all signal lines. |
| CE | Yes |
| UKCA | Yes |
| CRA (Cyber Resilience Act) | In preparation |
| ATEX | Zone 2, II 3G Ex nA nC IIA T5 Gc IP20, Ta (see X20 user's manual) FTZÚ 09 ATEX 0083X |
| UL | cULus E115267 Industrial control equipment |
| HazLoc | cCSAus 244665 Process control equipment for hazardous locations Class I, Division 2, Groups ABCD, T5 |
| KC | Yes |
| Type | SinCos |
| Angular position resolution | 13-bit, with a signal of 1 VSS |
| Encoder monitoring | Yes |
| Max. encoder cable length | Max. 20 m, see "Calculating the maximum encoder cable length". |
| Signal transmission | Differential signals, symmetrical |
| Signal frequency | DC up to 400 kHz |
| Differential voltage | 1 VSS |
| Common-mode voltage | Max. ±10 V |
| Terminating resistor | 120 Ω |
| Output voltage | 5 V |
| Min. output voltage at 300 mA | 4.86 V |
| Load capacity | 300 mA |
| Overload-proof | Yes |
| Short-circuit proof | Yes |
| Electrical isolation | Channel isolated from bus Channel not isolated from channel |
| Horizontal | Yes |
| Vertical | Yes |
| 0 to 2000 m | No limitation |
| >2000 m | Reduction of ambient temperature by 0.5°C per 100 m |
| Degree of protection per EN 60529 | IP20 |
| Horizontal mounting orientation | -25 to 60°C |
| Vertical mounting orientation | -25 to 50°C |
| Derating | See section "Derating". |
| Storage | 5 to 95%, non-condensing |
| Transport | 5 to 95%, non-condensing |
| Operation | 5 to 95%, non-condensing |
| Note | Order 1x terminal block X20TB12 separately. Order 1x bus module X20BM11 separately. |
| Pitch | 12.5+0.2 mm |
