B&R 80SD100XD.C044-01
Poproś o wycenę
Najważniejsze informacje
| Dostępność | Potwierdzenie na zapytanie |
| Kategoria | Stepper motor modules |
| Cykl życia | active |
| Gwarancja | 12 miesięcy (nowe) · 3 miesiące (używane/odnowione) |
| Waga | 650 kg |
Wysyłka i dostępność
Kiedy 80SD100XD.C044-01 może zostać wysłany?
80SD100XD.C044-01 jest sprowadzany na zamówienie — poproś o wycenę, a potwierdzimy dokładną dostępność i czas realizacji dla tej konkretnej sztuki.
Czy mogę odebrać 80SD100XD.C044-01 osobiście?
Odbiór osobisty w naszym magazynie w Groningen w Holandii może być możliwy — skontaktuj się z nami przed złożeniem zamówienia, aby potwierdzić dostępność i ustalić termin odbioru.
Czy dostępna jest dostawa ekspresowa?
Tak — wspomnij o tym w zapytaniu ofertowym dotyczącym 80SD100XD.C044-01, a w odpowiedzi podamy opcje dostawy ekspresowej.
Nasz zakład stoi i pilnie tego potrzebujemy — czy możecie pomóc?
W przypadku krytycznej awarii skontaktuj się z nami bezpośrednio pod numerem +31 (0)50-7110348 lub e-mailem sales@partnerplc.com — sprawdzimy możliwość kuriera tego samego dnia lub dedykowanego transportu dla 80SD100XD.C044-01, w zależności od dostępności i miejsca docelowego.
Control for 2 stepper motors (2-phase bipolar, full bridge)256 microsteps per step2 incremental encoder inputs2 trigger inputsMotor holding brake connectionEnable inputAutomatic motor identificationHolding, boost and continuous current can be defined independent of one another ACOPOSmicro stepper motor module, X2X Link interface, 2x 24 V incremental encoder, 24-64 VDC ±25% power supply, 2 motor connections, 10 A continuous current, 2 digital inputs 24 VDC, sink, can be used as trigger inputs, 1 digital output 24 VDC, 1 A, order terminal blocks separately!
Specyfikacja
Specifications
| Stepper motor module | Connection for 2 stepper motors with ABR incremental encoder, 2-phase bipolar |
| B&R ID code | 0xA781 |
| Status indicators | X2X Link, operating state, module status, motor information |
| Module run/error | Yes, using LED status indicator and software |
| Module temperature / Cooling unit temperature | Yes, using software |
| Motor status | Yes, using LED status indicator and software |
| X2X Link | Yes, using LED status indicator |
| CPU - 24 VDC power supply | No |
| CPU - Power supply | Yes |
| CPU - Motor connection | Yes |
| CPU - Digital inputs | Yes |
| CPU - Enable inputs | Yes |
| CPU - Encoder | No |
| CPU - Motor holding brake | No |
| CPU - X2X Link | Yes |
| CE | Yes |
| UKCA | Yes |
| CRA (Cyber Resilience Act) | In preparation |
| Functional safety | Yes |
| UL | cULus E225616 Power conversion equipment |
| KC | Yes |
| Input voltage | 24 VDC ±25% |
| Voltage monitoring | Yes |
| CPU | Max. 8 W |
| X2X Link power supply | Generated internally from the CPU power supply |
| Reverse polarity protection | Yes |
| Inrush current | Max. 10 A |
| Idle (no motor powered) | Max. 0.5 W |
| Full load | See diagram "Dimensioning - Power dissipation from the power unit for each powered axis" |
| Inrush current limiting | Yes, PTC (min. 9 Ω), is bypassed during operation by means of relay contact. |
| Undervoltage cutoff | <18 VDC |
| Overvoltage cutoff | >95 VDC |
| Voltage measurement | Yes |
| Line protection | Must occur externally |
| Quantity | 2 |
| Nominal current | 10 APeak |
| Max. current/motor | 15 APeak (2 s) |
| Max. current/module | 30 APeak |
| Nominal switching frequency | 38.5 kHz |
| Max. motor line length | 25 m |
| Step resolution | 256 microsteps per full step |
| DC bus capacitance | 940 µF |
| Nominal voltage | 24 VDC |
| Continuous current per connection | 1 A |
| Max. internal resistance | 0.3 Ω |
| Resistive load | 100 Hz |
| Inductive load | See section "Switching inductive loads" |
| Overload and short-circuit protection | Yes |
| Open-circuit monitoring | No |
| Undervoltage monitoring | Yes |
| Max. overcurrent limiting | 8 A |
| Response threshold for undervoltage monitoring | ≤11 VDC |
| Reference potential | GND for module power supply (X2 terminal, pin 10) |
| Variant | 4-pin male connector |
| Min. X2X Link cycle time | 250 μs |
| Type | KTY |
| Max. encoder cable length | 25 m |
| Output voltage | 24 V |
| Load capacity | 40 mA, important: 1 PTC for both encoder channels |
| Overload-proof | Yes |
| Short-circuit proof | Yes |
| Low | <5 VDC |
| High | >15 VDC |
| Values | 0 to 110 °C |
| Tolerance | 5% |
| Signal form | Square wave pulse |
| Evaluation | 4x |
| Counter size | 16-bit |
| Input frequency | Max. 50 kHz |
| Counter frequency | 200 kHz |
| Input current at nominal voltage | Approx. 7.5 mA |
| Input circuit | Sink |
| Maximum | 30 VDC |
| Insulation voltage between input and bus | 500 Veff |
| Input capacitance | 10 nF (Rev. < L0: 100 µF) |
| Additional functions | Can be used as trigger input |
| Nominal | 24 VDC |
| Input resistance | Approx. 3.2 kΩ |
| Rising edge | [Instant recording] Typ. 3 µs |
| Falling edge | [Instant recording] Typ. 4 µs |
| Input - ACOPOS | Yes, 500 Veff |
| Input - Input | Yes, 500 Veff |
| Modulation compared to ground potential | Max. ±38 V |
| Horizontal | No |
| Vertical | Yes |
| Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
| Degree of protection per EN 60529 | IP20 |
| Operation | 5 to 85 %, non-condensing |
| Storage | 5 to 95%, non-condensing |
| Transport | 5 to 95%, non-condensing |
| Note | Order terminal blocks and cables separately! |
| Mounting/Cooling | Screw mounting with heat spreader on mounting plate or cold-plate. |
| Width | 65 mm |
| Height | 134 mm |
| Depth | 95 mm |
| Weight | 650 g |
| Backplane | Always mount on conductive and earthed backplane. |
Więcej części B&R
UżywanyB&R 5C5001.01 IPC 5000 5D5500.06 Used
UżywanyB&R 5PC720.1505-K07 - 5P62:0A-03 Used