B&R X67BC7321-1
Solicitar orçamento
Dados rápidos
| Disponibilidade | Confirmação sob consulta |
| Categoria | Bus controller modules |
| Ciclo de vida | active |
| Garantia | 12 meses (novo) · 3 meses (usado/recondicionado) |
| Peso | 195 kg |
Envio e disponibilidade
Quando é que X67BC7321-1 pode ser enviado?
X67BC7321-1 é obtido sob encomenda — solicite um orçamento e confirmaremos a disponibilidade exata e o prazo de entrega para esta unidade específica.
Posso levantar X67BC7321-1 pessoalmente?
O levantamento no nosso armazém em Groningen, Países Baixos, pode ser possível — contacte-nos antes de encomendar para confirmar disponibilidade e combinar um horário de levantamento.
A entrega expresso está disponível?
Sim — mencione isso ao solicitar um orçamento para X67BC7321-1 e incluiremos as opções de entrega expresso na nossa resposta.
A nossa fábrica está parada e precisamos disto com urgência — podem ajudar?
Em caso de avaria crítica, contacte-nos diretamente através do +31 (0)50-7110348 ou sales@partnerplc.com — estudaremos um estafeta no mesmo dia ou transporte dedicado para X67BC7321-1, consoante a disponibilidade e o destino.
Fieldbus: CAN bus8 digital channels, configurable as inputs or outputsIntegrated I/O access in B&R Automation StudioAutomatic firmware update via the fieldbusX67 connection possibility for all B&R CPUs The bus controller makes it possible to connect X2X Link I/O nodes to CAN I/O. CAN I/O is a transfer protocol based on standard CAN bus that is fully integrated in the B&R system.Up to 43 logic I/O modules can be connected to the bus controller. Up to 16 of them can be analog modules.With multifunction modules, the bus controller supports only the default function model in the event of automatic configuration by the bus controller (see the respective module description).
Especificações
Specifications
| Bus controller | 0x18CB |
| Inputs/Outputs | 8x M8, 3-pin |
| Insulation voltage between channel and bus | 500 Veff |
| Nominal voltage | 24 VDC |
| Internal I/O module | 0x1311 |
| Sensor/Actuator power supply | Max. 12 W |
| Status indicators | I/O function per channel, supply voltage, bus function |
| Outputs | Yes, using LED status indicator and software |
| I/O power supply | M8, 4-pin |
| Fieldbus | CAN I/O |
| X2X Link | M12, B-coded |
| Power output | 3 W X2X Link power supply for I/O modules |
| Internal I/O | 2 W |
| X2X Link power supply | 6.2 W at maximum power output for connected I/O modules |
| CE | Yes |
| UKCA | Yes |
| CRA (Cyber Resilience Act) | In preparation |
| ATEX | Zone 2, II 3G Ex nA IIA T5 Gc IP67, Ta = 0 - Max. 60°C TÜV 05 ATEX 7201X |
| UL | cULus E115267 Industrial control equipment |
| HazLoc | cCSAus 244665 Process control equipment for hazardous locations Class I, Division 2, Groups ABCD, T5 |
| KC | Yes |
| Variant | Current-sourcing FET |
| Max. distance | 1000 m |
| Transfer rate | Max. 1 Mbit/s |
| Default transfer rate | Automatic transfer rate detection |
| X2X Link cycle time | Permanently set to 1 ms |
| Synchronization between bus systems possible | No |
| Terminating resistor | Can be optionally screwed onto the Y-connector |
| Voltage range | 18 to 30 VDC |
| Integrated protective function | Reverse polarity protection |
| Voltage | I/O power supply minus voltage drop for short-circuit protection |
| Voltage drop for short-circuit protection at 0.5 A | Max. 2 VDC |
| Summation current | Max. 0.5 A |
| Short-circuit proof | Yes |
| Input characteristics per EN 61131-2 | Type 1 |
| Input voltage | 18 to 30 VDC |
| Input current at 24 VDC | Typ. 4 mA |
| Input circuit | Sink |
| Hardware | ≤10 μs (channels 1 to 4) / ≤70 µs (channels 5 to 8) |
| Software | Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals |
| Input resistance | Typ. 6 kΩ |
| Additional functions | 50 kHz event counting, gate measurement |
| Low | <5 VDC |
| High | >15 VDC |
| Quantity | 1 |
| Signal form | Square wave pulse |
| Evaluation | Positive edge - Negative edge |
| Input frequency | Max. 50 kHz |
| Counter 1 | Input 1 |
| Counter 2 | Input 3 |
| Counter frequency | Max. 50 kHz |
| Counter size | 16-bit |
| Internal | 48 MHz, 3 MHz, 187.5 kHz |
| Length of pause between pulses | ≥100 µs |
| Pulse length | ≥20 µs |
| Supported inputs | Input 2 or input 4 |
| Switching voltage | I/O power supply minus residual voltage |
| Nominal output current | 0.5 A |
| Total nominal current | 4 A |
| Output circuit | Source |
| Output protection | Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply |
| Diagnostic status | Output monitoring with 10 ms delay |
| Leakage current when the output is switched off | 5 µA |
| Switching on after overload shutdown | Approx. 10 ms (depends on the module temperature) |
| Residual voltage | <0.3 V at 0.5 A nominal current |
| Peak short-circuit current | <12 A |
| 0 → 1 | <400 µs |
| 1 → 0 | <400 µs |
| Resistive load | Max. 100 Hz |
| Inductive load | See section "Switching inductive loads". |
| Braking voltage when switching off inductive loads | 50 VDC |
| Electrical isolation | Channel isolated from CAN I/O and bus CAN I/O not isolated from bus and channel not isolated from channel |
| Any | Yes |
| 0 to 2000 m | No limitation |
| >2000 m | Reduction of ambient temperature by 0.5°C per 100 m |
| Degree of protection per EN 60529 | IP67 |
| Operation | -25 to 60°C |
| Derating | - |
| Storage | -40 to 85°C |
| Transport | -40 to 85°C |
| Width | 53 mm |
| Height | 85 mm |
| Depth | 42 mm |
| Weight | 195 g |
| M8 | Max. 0.4 Nm |
| M12 | Max. 0.6 Nm |
Mais peças B&R
UsadoB&R 5C5001.01 IPC 5000 5D5500.06 Used
UsadoB&R 5PC720.1505-K07 - 5P62:0A-03 Used