B&R XEPIMC100

Name: B&R XEPIMC100
Brand: B&R
SKU: XEPIMC100

Referencia: XEPIMC100 · Marca: B&R

Precio bajo consulta

Solicitar presupuesto

Garantía de 12 meses (nuevo) · 3 meses (usado/reacondicionado)

Devoluciones en 30 días, sin comisión de reposición en piezas sin usar

Envío mediante

Datos rápidos

Disponibilidad	Confirmación bajo consulta
Ciclo de vida	active
Garantía	12 meses (nuevo) · 3 meses (usado/reacondicionado)

Envío y disponibilidad

¿Cuándo se puede enviar XEPIMC100?

XEPIMC100 se abastece bajo pedido — solicite un presupuesto y confirmaremos la disponibilidad exacta y el plazo de entrega para esta unidad concreta.

¿Puedo recoger XEPIMC100 en persona?

Es posible recoger el pedido en nuestro almacén de Groningen, Países Bajos — contáctenos antes de realizar el pedido para confirmar disponibilidad y acordar un horario de recogida.

¿Está disponible el envío exprés?

Sí — menciónelo al solicitar un presupuesto para XEPIMC100 e incluiremos las opciones de envío exprés en nuestra respuesta.

Nuestra planta está parada y lo necesitamos urgentemente — ¿pueden ayudar?

Ante una avería crítica, contáctenos directamente al +31 (0)50-7110348 o a sales@partnerplc.com — estudiaremos un envío urgente el mismo día o un transporte dedicado para XEPIMC100, según disponibilidad y destino.

CPU I/O board, ARM Cortex A8-600, 2 GB flash memory, 512 MB DDR3 SDRAM, 32 kB FRAM, 24 VDC, 2x Ethernet interface,1x CAN bus, 1x RS485 interface, 1x USB 2.0 interface, 35 digital inputs, 24 VDC, sink/source, 2 event counters or gate time / period duration measurement, 33 digital outputs, 24 VDC, 2 A (50%), 12 digital outputs, 24 VDC, 0.5 A, 2 PWM outputs, 3 A, 8 thermocouple inputs J, K, S, N, 4 analog inputs for potentiometers, 0 to 10 V, 0 to 20 mA, 4.5 V, 14-bit, 2 analog inputs ±10 V, 14-bit, 4 analog outputs, ±10 V, 12-bit

Especificaciones

Specifications

I/O module	35 digital inputs, 6 analog inputs, 45 digital outputs, 4 analog outputs, 8 thermocouples, 2 PWM outputs
Interfaces	2x Ethernet, 1x CAN bus, 1x RS485 interface, 1x USB
B&R ID code	0xF100
Automation Studio	4.5.01 or later
Automation Runtime	A4.51 or later
Cooling	Passive
Quantity	4
Status	Supply voltage OK, operating state, module status, Ethernet, CAN, RS485
Power button	No
Reset button	Yes
Master capability	No
Buzzer	No
ACOPOS support	No
Visual Components support	No
Safety support	No
Electrical isolation	Thermocouples, Ethernet 1 (IF2) and Ethernet 2 (IF3) isolated from each other and from other interfacesPower supply not isolated from channel, and channel not isolated from channel
CE	Yes
Bootloader	Automation RuntimeHardware revision ≥B0: AR 4.41
CompactFlash slot	0
Real-time clock	Yes, 1 s resolution, >±10 ppm accuracy at 25°C
FPU	Yes
Type	Push/Pull
Clock frequency	600 MHz
Data code	24 kB
Program code	32 kB
L2 cache	256 kB
Mode/Node switches	No
Remanent variables	32 kB FRAM, retention >10 years
Shortest task class cycle time	1 ms
Typical instruction cycle time	0.01 μs
RAM	512 MB DDR3 SDRAM
Data retention	10 years
Guaranteed	40 TB
Results for 5 years	21.9 GB/day
Guaranteed erase/write cycles	20,000
Error-correcting code (ECC)	Yes
Temperature cutoff	Yes
Connection designation	X4 RS485
Variant	Connection made using 0TB1110.9000
Line length	Max. 100 m between 2 nodes (segment length)
Max. transfer rate	10/100 Mbit/s
Physical layer	10BASE-T/100BASE-TX
Half-duplex	Yes
Full-duplex	Yes
Autonegotiation	Yes
Auto-MDI/MDIX	Yes
Current-carrying capacity	0.5 A
Transfer rate	Max. 115.2 kbit/s
Nominal voltage	24 VDC
Input voltage	24 VDC ±20%
Input current at 24 VDC	3.2 mA
Additional functions	Event counter, gate and period measurement
Circuit	Sink or source
Input delay	Counter inputs 1 to 2: <4 µsInputs 3 to 33: <1 ms
Low	<5 V
High	>15 V
Signal form	Square wave pulse
Evaluation	Positive or negative edge
Input frequency	Max. 100 kHz
Pulse length	10 µs
Counter size	16-bit
Supported inputs	Input 1: Counter 1Input 2: Counter 2
Internal	Yes
External	Max. 100 kHz
Length of pause between pulses	10 µs
Input	Inputs 1 and 2: ±10 VInputs 3 to 6: 0 to 10 V, 0 to 20 mA or 0 to 100% (Upot)
Input type	Inputs 1 and 2: Differential inputInputs 3 to 6: Single-ended input
Digital converter resolution	12-bit
Data type	INT
Voltage	INT 0x8000 - 0x7FFF / 1 LSB = 0x0010 = 4.88 mV
Current	0.004 %/°C
Current channel load	<400 Ω
Input protection	Protection against wiring with supply voltage
Gain	0.080%, based on the current output value
Offset	0.050%, based on the entire output range
Supply voltage UPot for potentiometer	4.5 V / Max. 50 mA
Measurement range	0.5 to 10 kΩ
Cutoff frequency	Inputs 1 and 2: 1 kHzInputs 3 to 6: 10 kHz
Slope	60 dB
Output format	INT
FeCuNi: Type J	-210 to 1200°C
NiCrNi: Type K	-270 to 1372°C
NiCrSi: Type N	-270 to 1300°C
PtRhPt: Type S	-50 to 1768°C
Sensor temperature	0.1°C/LSB
Type J: Fe-CuNi	±0.14% at 25°C
Type K: NiCr-Ni	±0.18% at 25°C
Type N: NiCrSi-NiSi	±0.16% at 25°C
Type S: PtRh10-Pt	±0.34% at 25°C
Basic accuracy at 25°C not taking Pt1000 sensor into account	±2°C after 10 minutes
Nominal output current	Screw clamp terminal blocks X12, X13 and X15:Per output: 2 APer group: 2 APer screw clamp terminal block: 11 AScrew clamp terminal blocks X14 and X16:Per output: 0.5 A
Output circuit	Sink
Output protection	Protection against wiring with supply voltage, short-circuit proof
Supply	External
Fuse	No internal fuse, the power supply of the outputs of each connector must be protected using a separate fuse of max. 15 A.
Switching frequency (resistive load)	Max. 100 Hz
Switching delay	Max. 500 µs
Supply voltage	Separately for each connector: 12 to 24 VDC ±20%
Supply voltage (permissible range)	External, 11 to 28 VDC
Nominal current	3 A
Maximum load current	3.5 A / output
Resistive load	≥8 Ω
Inductive load	≤10 mH
PWM frequency	15 Hz to 50 kHz
Configurable dither	Amplitude (8-bit), frequency (2 to 500 Hz)
Period duration resolution	16-bit
PWM mode	15-bit + sign≥1 µs
Current mode	15-bit + sign
Output	±10 V
Switch on/off behavior	Internal enable relay, for startup
10 V	0x7FFF
0 V	0x0000
-10 V	0x8000
Max. load per output	±10 mA (load ≥1 kΩ)
Max. gain drift	0.08%, based on the current output value
Max. offset drift	0.05%, based on the entire output range
Error caused by load change	0.015% from 10 MΩ → 1 kΩ, resistive
Nonlinearity	0.025%, based on the output range
Voltage range	24 VDC ±25%
Power consumption	3.5 W
Voltage monitoring	Yes
Horizontal	No
Vertical	Yes
Pollution degree per EN 60664-1	2
Operation	10 to 90%, non-condensing
Storage	5 to 95%, non-condensing
Transport	5 to 95%, non-condensing
Width	190 mm
Height	198 mm
Depth	31 mm
Module dimensions including mounting plates	190 x 198 x 31 mm (W x H x D)